ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES

Welcome, Guest. Please login or register.
Did you miss your activation email?
November 25, 2017, 01:40:49 AM
Home Help Search Login Register
News: Please read the Forum Code of Conduct   >>Click Here <<
+  Bachmann Message Board
|-+  Discussion Boards
| |-+  Large
| | |-+  how do i make custom model building signage
« previous next »
Pages: [1] Print
Author Topic: how do i make custom model building signage  (Read 1945 times)
robertalan51

View Profile
« on: February 12, 2012, 01:14:07 PM »

Hey guys, wondering if any of you have ever made your own signs for your model buildings. If  yes ...........how did you go about it? Are there computer programs for printing out custom made signage? What do you print them on? I've been trying to find out the answers to hese questions for a long time . HELP!!!!
Thanks, Rob
Logged
richg
Guest
« Reply #1 on: February 12, 2012, 05:38:48 PM »

You might find the answer below.

http://cs.trains.com/TRCCS/forums/t/162879.aspx?PageIndex=1

Rich
Logged
robertalan51

View Profile
« Reply #2 on: February 12, 2012, 07:51:50 PM »

Thanks Rich, very useful info indeed. I just need to find out how to produce custom made  store front signs in different sizes and fonts . Like "General Store"   " Dry Goods" etc etc.
Logged
Sleeping Bear

A genuine ALCOholic


View Profile
« Reply #3 on: February 12, 2012, 09:41:03 PM »

 I use inkjet water slide decal paper, make or modify designs in "paint" on my computer and print test pages on paper until I get size and color the way I want it. For signs, apply decals to lexan or sheet styrene. Before trying to even handle the water slide sheet after printing, give it 3-5 light coats of Krylon clear glaze to seal the ink to the paper or your fingers and the water will wipe them out. Have put custom decals on several Bachmann cars and with the help of Testors decal setting solution, they settle down into the cracks and gaps in the "wood" siding and you can see the grain in the wood through most. They look as though they were recently painted on. Be prepared to make a few runs till you get the amount of clear correct. Too much and it cracks and wont flex. Too little and the warm water and maybe the setting solution will bleed the ink. Had that happen on one reefer and I left it that way, kinda looks old and weathered.  This is the paper I use and have had good luck with.... http://www.ebay.com/itm/120661667228?ssPageName=STRK:MESINDXX:IT&_trksid=p3984.m1436.l2649   Hope this some help....Later All......S.B.
Logged

"If at first you don't succeed....Get a bigger hammer"
NarrowMinded


View Profile
« Reply #4 on: February 12, 2012, 10:12:53 PM »

I just did some signs for a 40's era gas station, I googled "free" printable vintage signs then went surfing the results, I found a lot of images, then printed them on plain paper and cut them out and built frames for some and use others as is like the are litho's on sheetmetal.

It's did take a little experimenting with sizing the images and print quality but that resulted in a net loss of 5 pieces of paper. Tongue

NM-Jeff
Logged
robertalan51

View Profile
« Reply #5 on: March 03, 2012, 08:58:31 AM »

thanks so much guys for your suggestions. I'll give 'em a try. Rob
Logged
Pages: [1] Print 
« previous next »
Jump to:  
Powered by SMF | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!