ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES

Welcome, Guest. Please login or register.
Did you miss your activation email?
November 24, 2017, 11:25:28 AM
Home Help Search Login Register
News: Check out the photo gallery link above or >click here< to see photos of recently announced products!
+  Bachmann Message Board
|-+  Discussion Boards
| |-+  HO
| | |-+  Stop & Go
« previous next »
Pages: [1] Print
Author Topic: Stop & Go  (Read 1328 times)
Mr. C

View Profile
« on: February 14, 2017, 04:31:09 PM »

I have a Berkshire 2-8-4 with dcc and sound. It came dcc equipped .I installed sound. It runs and works fine except when it crosses a particular switch.It has no trouble with the other switches. All other engines,whether dc or dcc cross it fine with no stop and go. I have to believe its something in the berkshire engine. I'm looking for ideas.
Logged
Irbricksceo


View Profile
« Reply #1 on: February 15, 2017, 03:02:48 AM »

Its possible that section of track is dirty. sound locomotives are much more sensitive to power loss (I actually removed the sound decoder from my only sound loco because it stalled too often, runs like a dream with a non-sound decoder in)
Logged
Mr. C

View Profile
« Reply #2 on: February 15, 2017, 04:42:00 PM »

Track has been cleaned.I replaced the switch. All other sound engines have no problem.
Logged
WoundedBear
A Derailed Drag Racer


View Profile WWW
« Reply #3 on: February 15, 2017, 04:54:07 PM »

Check your wiring on the loco. Almost sounds like some of the rail pick-ups aren't connected. Possible a cracked wire or something as simple as reseating the plug connectors between loco and tender. Also check pick-up wipers for wheel contact. A continuity test will tell you a lot about what is....or isn't.....connected.

Sid
Logged

Piyer


View Profile WWW
« Reply #4 on: February 15, 2017, 05:14:29 PM »

Is the turnout in question identical in all other aspects to the others? Same frog number? Wired the same? Is it flat or on a grade of even the slightest of sorts? Have you used a multi-meter to verify that all parts of the turnout are supply electricity where electricity is expected to be. Does the problem present itself regardless of direction of travel, or is the problem only happening when the locomotive crosses it in a specific routing?

~AJK
Logged

~AJ Kleipass~
Actively modeling in N, HO, and 2-rail O scales.
jbrock27

View Profile
« Reply #5 on: February 16, 2017, 08:20:23 AM »

We can assume this is a Bachmann turnout/switch, correct?
Logged

Keep Calm and Carry On
Mr. C

View Profile
« Reply #6 on: February 16, 2017, 10:22:58 AM »

I will check the engine for wiring faults. As for the turnouts,they are all the same.The problem happens in forward or reverse at that turnout. this is all Bachmann e-z track.
Logged
West Bound

View Profile
« Reply #7 on: February 16, 2017, 10:55:17 AM »

You may have already done these, Check the wheel wipers on loco are making good contact with the wheels. Move wheels side to side that they are still making contact. Check the wipers on the axles of the tender. also check to see if the plugs between loco and tender are tight.
Logged
HoModeler

View Profile
« Reply #8 on: February 19, 2017, 09:03:50 AM »

It could be the Decoder inside the engine LOST is PROGRAM OR is going BAD... I had an issue with a Non-Bachmann Loco A PA-1 A unit I have... Sort of the same issue you have but only my Loco would start up no problems & than start moving in a jerking / twitching motion & stop. Cleaned my Loco wheels & track to still have the same issues Took the Loco to my HS Train Tech he originally thought the Decoder LOST it's Programming So he re-programmed the Loco & brought it back home Loco Ran Good for 2 days than the same problem came back. I call the HS up & spoke to the Train Tech He said the Decoder WENT BAD thankfully the Loco was still under factory warrenty I sent loco in for repair.... The Factory sent me a New PA-1 A unit in the mail I had it 3 days later... I had NO Problems with the Loco since than....
Logged
Pages: [1] Print 
« previous next »
Jump to:  
Powered by SMF | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!