ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES

Welcome, Guest. Please login or register.
Did you miss your activation email?
November 17, 2017, 10:37:08 PM
Home Help Search Login Register
News: Check out the photo gallery link above or >click here< to see photos of recently announced products!
  Show Posts
Pages: 1 [2] 3 4
16  Discussion Boards / HO / 12 Volts on: April 22, 2016, 08:44:50 AM
I am running DCC command with a 5 amp power booster and when I check my track voltage it is only approx 9 volts. Why not 12?
17  Discussion Boards / HO / ACELA NO GO on: April 10, 2016, 12:30:57 PM
I have a Acela train with dcc on board,no sound, that has been running perfectly  for 2+ years. All of a sudden it stopped working. I have checked the track with other engines and everything is fine.Before I take it apart,any suggestions as to what to look for?
18  Discussion Boards / General Discussion / #44910 5 amp power booster problem on: November 08, 2015, 10:28:59 AM
I have discovered that the 12volt output is not working to the track. There is a switch to change this to 14volt.Has anybody done this for ho track ?
Bachmann does not repair this item, so I am forced to purchase a new one.
19  Discussion Boards / HO / Re: slow speed on: October 06, 2014, 12:44:19 PM
Thanks everyone for your input and the websites you suggest for more info.
I will truly treasure this engine.
20  Discussion Boards / HO / slow speed on: October 04, 2014, 02:35:08 PM
I have a 70 ton 3 truck climax that I think could run faster than it does. Is there a way to increase factory speed,and how do you do it?
21  Discussion Boards / HO / sound on my fp40 on: October 01, 2014, 09:52:06 AM
I have a Bachmann diesel fp40 with dcc and would like to add sound. what should I buy to do this and how to install it.
22  Discussion Boards / HO / upgrading on: September 15, 2014, 02:17:48 PM
I am using the ez command system at the present time #44902 and would like to upgrade to a larger system like the dynamis system.
Any ideas?
23  Discussion Boards / HO / Re: dcc switch on: December 21, 2013, 02:47:54 PM
Answer to question #1 is NO it only occurs after running any engine.
#2 is yes  any engine ie rs2 and 3
24  Discussion Boards / HO / Re: dcc switch on: December 16, 2013, 06:02:15 PM
FYI all of the engines and equipment are Bachmann installed decoders.I don't understand why when you run an engine the turnout switch stops working.
25  Discussion Boards / HO / dcc switch on: December 16, 2013, 04:21:24 PM
I have a dcc switch running on the ez command system. I have programmed it according to the instructions and it works the first time I turn power on.
That is push #9,then function,then I use #3 to switch it.After I run any other engine on another 3(2or4etc) then come back to switch it,it doesn't work.

Help
26  Discussion Boards / HO / Re: programming a turnout on: November 23, 2013, 03:49:39 PM
I'm using the ez command system. I went in and followed those directions .When I finished programing the switch cycled  4 times telling me it was programed successfully. Now,how is the switch supposed to toggle back and forth.I thought you pushed the forward and reverse arrows to toggle it ---nothing
27  Discussion Boards / HO / programming a turnout on: November 23, 2013, 03:26:24 PM
I purchased a #6 turnout and followed the directions.Everything programmed as it was supposed to but,the switch does not toggle back and forth when I hit either direction button.
28  Discussion Boards / HO / Re: faulty switches on: November 02, 2013, 04:07:53 PM
Yes,the both are,but are located in different locations on the layout.I have a 5amp power booster that I thought would alleviate the problem.
29  Discussion Boards / HO / Re: DCC switch on: November 02, 2013, 04:04:58 PM
I found it    thanks again
30  Discussion Boards / HO / Re: faulty switches on: November 02, 2013, 02:58:38 PM
I've checked and replaced everything.I've also taken one motor apart and checked it. I can get it to work a couple of times and then it stops.
Pages: 1 [2] 3 4
Powered by SMF | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!