News:

Please read the Forum Code of Conduct   >>Click Here <<

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - wally

#16
On30 / DCC and DC ON THE SAME TRACK
January 13, 2008, 12:18:33 PM
I have a nce power cab for my Bachmann ON30 engines. It does not support dc engines. Can I use a dpdt toggle switch and run a regular dc transformer through it and switch between dcc or dc on the same track.Thanks Wally
#17
On30 / DCC for Climax
January 07, 2008, 03:50:54 PM
Is there a chip that will just plug in to the Bachmann on30 climax that does not have sound,just motor control? Help would be greatly appreciated.
#18
On30 / Re: 4-4-0 Size
January 01, 2008, 11:01:13 AM
Thanks for the help. Wally
#19
On30 / 4-4-0 Size
December 31, 2007, 10:09:29 PM

Can someone please give me the length of the Bachman 4-4-0 on30 engine and tender?  And the heighth of the engine at the stack.  Thanks, Wally
#20
General Discussion / Re: CA storage life
November 21, 2007, 04:24:53 PM
I use  the ca called Zap-A-Gap . I keep it in the fridge on one of the drink shelves. It stays for month's. You don't need to freeze it.
#21
On30 / Frog stalling
August 25, 2007, 12:27:47 PM
I have some kato manual switches, and I am having trouble with a Bachmann Shay stalling on the switches.There are 2 ways you can set the switch, power and none power. It says to use non power routing for dcc, Powered routing can cause a short if the closed line of the rail touches the open line. If I tried the closed line would that help the stalling, or is there another way to stop the stalling with the Kato switch. Thanks foe any help. Wally
#22
On30 / Re: Kadee 148 Couplers
August 25, 2007, 12:20:37 PM
Thanks fellows for the advice. Wally
#23
On30 / Kadee 148 Couplers
August 24, 2007, 07:20:11 PM
Has anyone tried the Kadee 148 couplers in there Bachmann on30 cars and engines? Is there any advantage to the # 5 coupler compared to the 148?  Should I stay with the couplers that come with the cars? Any help appreciated. Just getting started. Wally
#24
On30 / Bachmann Climax
August 19, 2007, 05:02:49 PM
I am new to DCC and have a question about the Bachmann on30 climax. What type of decoder do I need to have both sound and control? Do I need to solder for installation, or is there one that just plugs in? Any help greatly appreciated.
#25
On30 / Forney and 18 inch radius curves
May 16, 2007, 03:28:34 PM
Will the new Forney handle 18 inch radius curves? Thanks Wally
#26
On30 / on30 and E-Z Command
April 17, 2007, 02:21:19 PM
How does the E-Z Command system work with the Bachmann on30 engines with Tsunami sound? Has anyone had experience with this?Thanks Wally
#27
HO / Re: EZ Command and Sound
March 29, 2007, 02:31:57 PM
Thank You Bachmann. Wally
#28
HO / EZ Command and Sound
March 28, 2007, 08:00:05 PM
Will the ez command system work all of the sounds on the new Bachmann engines with sound installed? Any help will be appreciated.Thanks Wally
#29
Large / Re: Bachmann DCC and G Scale
February 22, 2007, 03:08:04 PM
Thanks for the help.
#30
Large / Bachmann DCC and G Scale
February 21, 2007, 04:26:28 PM
Will the Bachmann DCC E-Z digital command control system work with  Bachmanns own G scale engines that come DCC ready?