Personally, I do not think the switches that come with EZ track remote turnouts are the best looking.  I would like to use toggle switches (toggle may not be the right term, but I mean the little metal switch that has the pin sticking out). Eventually I would like to get a drawing of my layout and place the switches in the appropriate places.

What type switches do I need?  I know they need to be momentary, but do they need to be SPDT or DPDT or something else entirely?  Do the wye turnouts require different switches?  I ask because Bachmann uses a different switch for them.  Do you have any recommendation on particular switches to use for this application?

thanks in advance for your help

I have five locomotives that I have collected so far (including one that was DOA and I am still waiting on getting it repaired).  Two are DC, two are DCC, and my most recent purchase is DCC with sound.  When I put that loco on my plain track last night for the first time, it was like I was a kid all over again.  Immediately it became my favorite even though it is a switcher with limited function for my overall layout.

I must purchase another DCC with sound engine for hauling long consists around the track.  I am probably also going to buy the Bachmann Dynamis controller to access more of the sounds with my new loco than my EZ DCC controller can.

What is your favorite DCC locomotive (steam or diesel) with sound?  I want one that will handle 18" curves with no problem.  I am looking more for fun than some sophisticated rare locomotive that represents some obscure prototype from one particular year.  

I went to the hobby shop at lunch today (big mistake because I spent too much and took too long).  Part of my purchases were EZ track left and right remote turnout.  Another purchase was an awesome Broadway Limited NW2 switcher.  As I am playing with my new track and engine, I discovered that the left-turnout when selected toward the turnout causes the switcher to often derail, especially when in reverse with a load but can happen going forward as well.  I then tested it with my Bachmann GT40 engine with no problems.  However, the right-turnout when selected toward the turnout causes the GT40 to often derail but never the switcher.  Why would each of these engines have problems with separate turnouts?  I am using the track on a kitchen countertop because I have not yet built my permanent layout.

I have been looking for the best deals to buy EZ track because I am about to buy a ton of it.  I am new to this hobby and don't know all the players.  I found a good deal for the pieces I am looking for at www.trainsetsonly.com.  Are they a reputable dealer?  I hate to give an online company hundreds of dollars without knowing if they are a legit company or not.

Thanks for your help.

I am hoping to start ordering track this weekend for my first layout.  I am so excited, but I am not 100% clear on wiring.  Per someone's earlier recommendation to me, I bought the Atlas layout book (I purchased the Bachmann one first).  Track plan 206, "The Out-And-Back" is what most appeals to me with some modifications.

Modification (and question) #1.  I have both Bachmann DCC and DC controllers and I am hoping to use both with this layout because I have both styles of engines.  I assume that I will not need all those blocks of controllers and selectors because I will have at most 1 DC engine running on my layout along with my DCC engines.  Am I right in assuming that this will not be needed?

Question #2. This layout has a reversing loop in it.  Should I just isolate that section or do I need to use a Bachmann reversing loop?  Is this section going to present a problem if I am running a single DC locomotive?

Question #3.  I am planning on modifying the layout in a fairly significant way.  Rather than having the railyard and turntable where the plan has it, I want to have the track go underneath the layout in a big loop then come back out the front of the layout where I will put in a larger railyard and a switching section like the Bachmann "Time-saver" plan.  My question here is I have read to keep your grades at 4% or less.  Is this for realism or for function?  The area I think may have a greater than 4% grade would be hidden, so realism is not needed.

Here is my basic plan for this layout.  The red lines idicate that it is underneath the main tabletop.  The railyard would be in front of the rest of the table, slightly lower.  Thanks for all your comments and help.

I received a DCC Commander set for Christmas and now want to build a table.  After looking at dozens and dozens of layouts, I have come up with a plan close to what I want to do.  There is one trick to it that I am unsure of. 

Here is a simple version of what I am planning on, which I have taken from thortrains.net.  It has a reversing section on it.


Since I am using a DCC setup, should I just have gaps between the two turnouts from the main loop and the turnout inside the spur?  Then should I connect a second terminal/rerailler on the spur to a Bachmann DCC Automatic Reverse Loop Module?

I have not purchased the track or the module to do any of this yet, but I would like a clear picture in my head before I start spending hundreds of dollars on track.

Thanks,

George

I posted on this forum earlier about my new locomotive having issues.  I called Bachmann this morning at 9:00 eastern and sent in an online request for help a few minutes later.  It is now 3:45 eastern and I still have not received a call back.  I have called a couple of other times throughout the day and hung up without leaving another voice message.  They close at 4:00 eastern.  Are they open today or is this typical for their service department?

When we were decorating for Christmas this year, I pulled out the HO trainset my father built for me for the Christmas when I was 6.  Now I have a grandson and want him to experience having model trains.  He absolutely loved watching my old train go around the tree.  

For Christmas I received a Digital Commander set (2 engines).  I set it up on the floor and plugged it in.  The first engine worked great.  The second engine caused the stop and #1 lights to flash rapidly on the controller while making rapid chirping sounds.  I worked for at least 30 minutes unplugging/replugging tracks and controller.  I reprogrammed the other engine and anything else I could think of to get it working.  I discovered that when the lights flash like that, there is a short.  Could the engine be causing the short?

I do have a second question.  Where can I find some sort of dummies guide to HO model railroading?  I don't know things like the difference between #5 and #6 turnouts or what additional items I need to get a turnout to work with my DCC controller.

Thanks in advance for any help.