Good morning.
I remember reading somewhere that HO switch stands are too large to be scale prototype.
If this is true, would one be better off using N scale stands on an HO setup?
Thanks.
ErnieK
Usually the N scale ones don't have enough throwbar travel to work with an HO turnout.
Sid
Thanks Bear
Quote from: WoundedBear on September 16, 2016, 01:00:29 PM
Usually the N scale ones don't have enough throwbar travel to work with an HO turnout.
Sid
Hmmmm.....I have read quite a bit of a lot of folks successfully using them ??? And the reason they do, is they look better as the Ns are more to scale looking than the HO versions.
For example,
Doc Wayne:
Posted by doctorwayne on Tuesday, February 17, 2015 2:56 PM
I use mostly the 202S and 206S ones, with a couple of 220S models where needed. All, including the 206S, which are meant for N scale, work well with Atlas, Shinohara, and Micro Engineering HO scale turnouts.
The only modification to use them with Atlas code 83 turnouts is to remove the raised nub from near the end of the Atlas throwbar, although the code 100 turnouts may have a different arrangement.Wayne
'member him?? ;)
I remember him......another one that seems to have disappeared.
Jim.....look at this page. https://www.walthers.com/caboose-industries (https://www.walthers.com/caboose-industries)
I don't know how you get the N ones to work with that little of drawbar movement. Do you relocate the attachment point? I know I tried using HO ones on N turnouts when I was playing around with the HOn30 scene......never could get them to work and had to swap for proper N scale ones.
If the drawbar travel is too little, I don't see how they could successfully throw the points. But then again....what do I know?
Sid
I'm using these on my layout.
https://www.walthers.com/high-level-switch-stand-190-quot-travel-sprung-w-lantern-targets
They work really well. A little oversize but so what. To me they look better than the more popular ground throws.
I bent the throw bar down a little which helps the appearance. I'm waiting to finish the scenery around them before installing the targets.
Quote from: WoundedBear on September 16, 2016, 06:29:28 PM
......another one that seems to have disappeared.
I don't know how you get the N ones to work with that little of drawbar movement.
I know I tried using HO ones on N turnouts when I was playing around with the HOn30 scene......never could get them to work...
Sid
-Yep, packed up his tent took his stuff and went back over to MRR...
-I don't have the answer for ya
Sid, sorry. Some research may shed some light. Clearly the
Doc and others have had success doing it.
-Never heard of anyone trying it on the other direction like you did, using HO for N, only the other way, N for HO, with success.
What is MRR?
It's probably already been considered but I'm still going to raise the question of which size ground throws can one's 1:1 scale fingers reliably work over the passage of time?
Dear All,
I highly recommend Caboose Industries switch stands. They look and work great!
the Bach-man
Quote from: Trainman203 on September 16, 2016, 10:34:32 PM
What is MRR?
Model Railroader as in forum.
Quote from: the Bach-man on September 16, 2016, 11:41:04 PM
Dear All,
I highly recommend Caboose Industries switch stands. They look and work great!
the Bach-man
That is great to know. But, if that is the sentiment, then how come one a y'all, most likely the
Yardmaster, I would guess, Deleted the 2 threads started by
RAM about Caboose Hobbies going out of business ??? ::)
Caboose Hobbies, the hobby shop that is closing, is not the same as Caboose Industries, that makes the switch stands and is still open.
Len
My misunderstanding. Thanks for pointing that out Len and for clarifying. My apologies for any confusion.
Caboose Hobbies is in CO, correct? Where is Caboose Industries headquartered?
Caboose Industries is in Freeport, Illinois.
Len
They are very approachable. I called about replacing some lost parts and the guy as totally polite and helpful.
Thank you both for the info.
Quote from: WoundedBear on September 16, 2016, 06:29:28 PM
I remember him......another one that seems to have disappeared.
Jim.....look at this page. https://www.walthers.com/caboose-industries (https://www.walthers.com/caboose-industries)
I don't know how you get the N ones to work with that little of drawbar movement. Do you relocate the attachment point? I know I tried using HO ones on N turnouts when I was playing around with the HOn30 scene......never could get them to work and had to swap for proper N scale ones.
If the drawbar travel is too little, I don't see how they could successfully throw the points. But then again....what do I know?
Sid
sid,
is you want to adjust the travel in the points, it is a simple surgery to replace the throwbars with a strip of pc board, and solder the points to this. you can adjust the points to suit the switchstand, rather than trying to adjust the switchstand to the points.
I use Caboose Industries N scale ground throws on all my HO layouts and they work fine. I use Peco and Micro Engineering turnouts along with a smattering of Shinoharas and have not had any problems. They look substantially better than the HO ones too.