does anyone have this...does the loader stay on the flat car and does it come off also http://www.mthtrains.com/content/80-98016

My boss found this upstairs at the shop and we got it running after a little over oiling...I told him not to flood it he says its been up there at least 30 yrs...hes 53 

Here is my little engineer for another run http://www.youtube.com/watch?v=AEYzf6keoR0

this is for my soon to be 5yo http://cgi.ebay.com/New-Nordicware-Williams-Sonoma-Train-Cake-Pan-4-Thomas_W0QQitemZ290305014970QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item439786fcba

what would be a good layout mat (green) there are numerous choices and I don't want low quality

is there a curved bridge without track in 22" radius that will allow the ez track to go on

I would like to make a tunnel for the layout...I know to use chicken wire for the frame but my question is ...does the plaser of paris rolls work well for covering the wire and then painting

will these fit ez track to isolate a spur http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170384201307&ssPageName=ADME:X:AAQ:US:1123

 I have looked for it but I don't see it...is there a 22" radius terminal rerailer available in Bachmann ez track, I have a section that shows 22v on the volt meter but all the trains slow down going thru it and I would like to add a terminal in the curve...no straight is close enough, after the curve they speed back up...its hardly enough to notice but it will drive me crazy till its better

ok this is the new diesel...I was wonder if I want to make a consist with one just like it or would it be bad if they have the same road number , is there a dummy engine like this or should I get another one just like it and run them back to back...since they are the same they should run the same and it would be easy with the ez command http://www.bachmanntrains.com/home-usa/products.php?act=viewProd&productId=278

just thought I would share

I got the #6 turnouts today and couldn't wait till tomorrow to put them in so here are a few pics...also the new diesel

what is a good steam engine for 18" radius curves...I think the 2-8-0 that has hit the floor 3 times has had it ...it runs but it is like it is dragging at certain spots ... almost like it is rubbing internally and slows way down then speeds back up, both other engines run fine w/o problem...should I get another 2-8-0 or would there be a better choice for about the same price...I have to replace it as my little engineer want an engine that will run the whole track, the other two don't like the 18"...thanks in advance

got 2 of these for my sidings  http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=120534418866&ssPageName=STRK:MEWAX:IT

does anyone know the length of the Bachmann #4 , #5 and #6 turnouts...straight side

Is this a good engine... http://www.bachmanntrains.com/home-usa/products.php?act=viewProd&productId=278

I got the Bachmann Spectrum explorer set with a 2-8-0...what the difference in this 2-8-0... http://www.trainsetsonly.com/page/TSO/PROD/160-51302

how does the top come off the Acela express...decoder goin in

is this a good decoder for the Acela the ad says it has adjustable start voltage...does the ez command have this option http://cgi.ebay.com/BACHMANN-SPECTRUM-LOCO-TRAIN-DECODER-N-HO-ON30-44915_W0QQitemZ120486121038QQcmdZViewItemQQptZModel_RR_Trains?hash=item1c0d884e4e

the engines kinda whine when starting off , any reason or is this bad for the engines ... also which decoder would be good for the Acela Express for speed direction and lighting