Good morning
Am looking at the roco Z21 system as a replacement for my dynamis controller , is the Roco  system compatible with Bachmann  svc exit track turnouts?

Hi all
I use ezitrack with dcc turnouts and dynamis controller.
How hard is it to install track signals?
Do Bachmann have any ready to install products available?
Kind Regards

Hi All ,  I am building a totally  dcc layout using dynamis and ezitrack (with dcc turnouts),  would like to include automated block signals into it..
What is available ? Are there any block signals that can simply plug into the existing turnouts?
Your input and experience will be greatly appreciated.

Good morning, have sent emails to both parts and service  (including one to wallaceb@bachmanntrains.com , this address I  found in the forum , and received an incorrect address notification when i sent it.).so far I have had no response  (s) ,  I am in Australia  and  would like some contact information please.

Hi ,  am considering using the N scale auto reverse set as a mining operation on a larger scale build.
What are the requirements for the Loco  ,  dc/dcc ,  can't find any relevant information.
Thanks and kind regards
Marshall Spencer

Hi , am using Ezitrack nickel silver , what is the best way of laying down ballast on this type of track (HO) especially on and around turnouts (full DCC).
Thank You

Hi , I have a Dynamis operating system , all my turnouts are DCC operated , when I go into the programming mode , everything goes as per the instructions. When I turn the controller off to save battery power and turn back on again, all saved addresses for the turnouts appear to have been wiped out... what step am I missing.

I have a Spectrum DCC and Sound , Baldwin 2-8-0 consolidation with medium tender #84509 , the leading tender truck does not want to keep sitting squarely on the rails , possibly the DCC wiring harness is lifting the front of the tender , or there is not enough weight in the tender ...any ideas guys ?

Hi Mr.Bachmann , I have recently purchased some 44132 and 44133 DCC E-Z Track turnouts , when fitting other track components i.e. 44511 straights , have found that the roadbeds, foul on the track beside it .. Question is do I have to trim the roadbed on both tracks , if so , by how much and at what angle is recommended ?

HI , have recently purchased a Spectrum/Dynamis Starter set Maine Central #01403 and a catalogue #99978.Will be using an 8x4 area , purely for lack of any other useable room ..
The track plans/layouts in the E-Ztrack catalogue are minimal , I will be using nickel silver E-Z track , with DCC controlled turnouts etc.
Are there any other reference catalogues for suitable track plans available through Bachmann? have also downladed the "free version of Anyrail.com"
Thank you

Hi , have recently purchased a dynamis starter set .
With the power feed to the rerailer , can I splice another power feed to the current one and how many times can I splice to other rerailer feeds , before there is any noticeable/major issues with power , amperage , voltage drops?

HI all , as a total novice to DCC , which would be a better starting point : E-Z command or Dynamis ??

Hi , am about to start my first DCC layout , will purchase a basic E-Z command unit and engine , and a track starter pack.
I notice that on the back of the controller , there is only one jacking point for power to the track via the rerailer , if I was to use several rerailers , can these also be hooked up to the basic controller or to each other in series??
I am a total novice to all this , so come on guys , would love some serious help here..

Hi , I am I Australia and am looking at purchasing a Bachmann starter pack (E-Z command controller , DCC engine and carriages locally ) will purchase the track starter pack from Bachmann at a later date.
I have asked several local dealers , as to what also will be needed to be purchased , to control turnouts , i.e. separate power supply , switches , controllers , wiring etc. and especially what is required for the DCC turnouts.
The replies thus far have been mixed and basically know one knows.. there seems to be a distinct lack of printed information available to dealers.
I have looked at the forum boards , and mostly it directs you to another part of the Bachmann site , but this at best is quite confusing and still doesn't answer my fundamental question.. "What else is needed to control turnouts on a DCC system , ie separate power supplies , switches/controls , wiring etc."
Please Mr.Bachmann , can you shed some simple light on this?