Hello,  I have the Bachmann DD40AX with the sound value decoder, my issue is the volume of the prime mover's, bell and horn can not be adjusted even the master volume I have set the corresponding CVs above the default settings to no avail. other sound value engines are much louder in all aspects. I checked speaker wires and all seem to be connected. what is the next course of action. thanks

Hello
I have a Bachmann DD40AX sound value Engine, The issue I have is the sound of the horn and prime movers is very low compared to the bell sound, even after changing the CVs I can't seem to increase the horn or prime mover volume, but I can increase or decrease the bell volume I have tried the master volume CV and the volume does not increase. what if any thing am i missing?

Thanks

Wondering if Bachmann would consider producing a GP15-1 (Frisco version) In the Wisconsin Northern version Road # 1501 and 1502, These are used in the sand industry.

I have the Bachmann DD40AX sound value.
I can set all cvs except the cvs 193and 194 (bell on set point and bell off set point) i have tried the
default values of 05 and 10, i am using a Digitrax Zephry,  again I can change all other cvs but those two.

I seen a picture of this engine, I think the engine is a Bachmann DD40AX very old #6922 there is a battery compartment on the bottom center. not sure what that would be, does any one know?

I have a new Bachmann DD40AX with sound, it worked perfect out of the box, but now it runs and all the lights work fine but the sound keeps shutting off while standing still, it did not do this at first, but as soon as i move the throttle in restarts the sound, I am using a Digitrax Zephr extra.

Hello
I bought a new DD40AX W/sound and trying to find out how many CVs can be changed, the paper work that came with it does not say any thing about the Sound decoder CVs, were can i find that information.

Thanks for any help

Hello
I have a Bachmann 2-8-2 Mikado road # 2528 and can not find the parts sheet on the Bachmann web site, I have looked many times thinking i just missed it, any help in finding were i can find one.

Thanks
Dan

Just recieved a new GB38 with DCC onboard, this is my first Bachmann engine, when i put it on the layout and increase the throttle the motor buzzs and will not move unless the throttle is at about full and the same for reverse, could this be a CV setting oir do you think it is deffective unit?

Thanks
Dan

Hello

I have a chance to buy a new Bachmann plus F7 A & B powered unit, My ? is, are this engines worth spending the money to put DCC with sound, the engines are selling for $25.00 for the pair.

Thanks

Hello

I bought a new Bachmann EMD SD40-2 DCC equipped, I am waiting for it to come in at LHS.
my ? is is there room in the shell to add a speaker and replace the decoder and is it a plug and play?   ( there on backorder )

Thanks

I picked up a Bachmann Overland 4-8-4 at a flea market as is. so it was no surprise that it did not run, I plan on sending it in for repair.

My ?  is if requested, could they make it DCC ready with a quick plug.


Thanks for any comments.

Hello fellow Model RailRoaders

I Have  a Trix BigBoy with V3.0 Loxsound 2004, I am using a Digitrax Zephyr Extra controller with 29 function keys, i can not get the airpump sound to shut of and i have been on the Loksound dissusion site and no help from them, does any body have and suggestions on how to help?

Very Frustrated
Thanks

Dan

I have a new EMD GP38-2 DC, (blue box item 61712)  I removed the pcb13 board and wired in a athrean dcc ready board with a quick plug, i pluged in a decoder and the engine runs fine forward and backwards, the problem is the lights will not work in either derection, i checked the lights and they are not burnt out , they light up using another power source, they are not LED.

Thanks DAn\\an

Hello, are the front and back lights in the Bachmann GP38-2 Led?


Thanks Dan

HI just bought a Bachmann GP38-2 DC, I want to convert it to DCC withsoundany suggestions on the best way to install it and best place for the speaker, also decoder and speaker brand suggestions.     


Thank You

 I bought this engine used from a person that was using the EZ command. he had 8 functions set up. i'am using the zephry extra with 29 functions. i can not find any information on how many functions this decoder has or how to add functions can this be fixed or am i better off switching it to a Tsunami?  Ive been thru the loksound web page and the loksound manuel and have not found any information.     Any help would be appreciated

Has any one installed a DCC with sound decoder in a Bachman Overland 4-8-4 union Pacific?
this a older engine but looks and runs very nice and i would like to install dcc with sound, any pics or derections would be very helpful.


Thanks

Just purchased a used 4-8-8-4 DCC W/sound, the Engine and tender are VERY DUSTY any suggestions on how to clean this? my 3year old grand daughter says just put in the dishwasher papa.

Looking for instuctions on how to convert this engine to DCC W/ sound, this ia a older engine with tender.