I'm working on a continuous new layout. The Engine will start out on the right of a double track, that continues to a loop (no switch ), returns on left side of starter track to another loop (no switch) that returns engine to starting point. I do not see a reverse loop, but several on this forum did, so I purchased a Auto Reverser circuit.and installed the Insulated joiners. in one loop.
The Engine stalls and stops going from the one side to the other. I can't get continuous running. I've been experimenting with insulated joiners in the other loop with temporary DCC connections. No way can I get the continuous run. Always a Stall and stop. Push passed the insulated joiners,runs fine with correct direction. Before the Auto reverser and insulated joiners I did get shorted out. I think it's a great plan but can't overcome the stop then push.
Any help really appreciated.
Joe

It's a new one on me. Just finished laying track for a new layout. I'm using DCC that I've used before. My layout is simple enough to me. Its double track with a return loop at both ends. the return loops themselves are single track. A double track entering the loop by going to single track then meeting the double track again after completing the loop heading other direction. I have crossovers between the double track at one point. Powered the track up and could not get continual juice. (shorted ) I then disconnected the track in 2 spots, Powered up fine. Reconnect track and shorted out. The only tester I have is a DC meter. I put insulated joiners where I had disconnected. Power great on both sides of disconnect now isolated. Tested with my meter, and on one side of the insulated joiner , I have + on left side. The other side of insulated joiner has a - on left side.  I'm afraid to run an engine over this point. Seems in earlier years I had reverse loops and used a reverse loop switch  that had to be thrown while train was in reverse loop. I do not have reverse loops now. Can anyone explain my problem and a solution ? BTW I do use the Bachmann E Z Command and had crossovers on previous layouts with no problems .

is there any way to program the master volume on the H-0  E Z command unit. I recently installed a decoder in an older Diesel and the volume blows my ears off. The seller has offered to reset the unit off  "Default"  and lower the volume, if I return it. Before I go through the expense of shipping snd packing both ways thought best to post this on the forum.
Joe W

I have 2-- 11 1/2 " H-0 passenger cars. Bought new about 4 years ago. Never ran them as they wouldn't clear my tunnels. I can find no markings as to who the manufactor is. Just placed them on a test track and no lights. The pickups are working from the trucks to the floor of the body and contact transfer beyond looks fine. I can't see any lights in in the interior ceilings through the windows. These cars are hard to get apart and I don't want to dismantle any further. My layout is DCC I have tried DCC current in the track and the old DC . Nothing. Any clue as to who made these cars ? I'd like to contact the MFG for help . Well made, beautiful cars, Interior details etc.
Joe

 As usual I've misplaced the directions for the E Z Command unit. I'm fine with the use of 1 Controller. A few years back I purchased a second controller so 2 persons could run trains. I'm at a loss as to how to connect up the 2 units. The instructions I've printed, out state to connect the black interconnecting cable provide. I see a USB or similar port marked I/O but see no means to connect the 2 units into that port. I have the 2 wires that have the correct plug in to the I/O but the other ends are telephone (similar ) jacks. Trying to get this wired for a Christmas display so visitors can run a train. All help will be appreciated. Thanks.
Joe

Depending on the Decoder, I read that certain whistle bell and other sounds can be changed. Or reprogrammed. What is required to do this ?
Computer, USB cable, track, software. I want to get my feet wet and have no idea what I need.             Thanks

Mr Bachmann
Have recently purchased 2 Bachmann Engines that have DCC.  I want to add sound. Neither engine has a DCC board that will accept a 'plug in'. Where do I go from here ? Can sound be added ?