Title: Homemade details for Glenbrook Valley 4-6-0
Post by: on30gn15 on May 20, 2011, 06:38:44 PM
Post by: on30gn15 on May 20, 2011, 06:38:44 PM
Hey Y'all;
Slooooooowwwwly plodding along. Have had good days this week taking an hour here and there to add some homemade details to Glenbrook Valley 4-6-0 Big Hauler.
Bell rope from model ship rigging thread. Craft eye-pin provided guide loop at base of steam dome.
(still need to replace whistle from last year when Georgie knocked a shelf down on loco siting on floor)
Classification flag holders from odds and ends of brass and plastic with paper flags - white for running extra (as in not a scheduled train)
(Also note loco was changed from wood-burner it came as to a coal burner)
Also pilot deck from Plastruct treadplate sheet. Real one of this vintage likely was not treadplate but I like the visual texture. Plate still needs side sills added.
Control rod and lever for sand dome made out of brass wire and strip. Strip is press fit into slot made by drilling 3 holes then nibbling between with #11 blade.
Slooooooowwwwly plodding along. Have had good days this week taking an hour here and there to add some homemade details to Glenbrook Valley 4-6-0 Big Hauler.
Bell rope from model ship rigging thread. Craft eye-pin provided guide loop at base of steam dome.
(still need to replace whistle from last year when Georgie knocked a shelf down on loco siting on floor)
Classification flag holders from odds and ends of brass and plastic with paper flags - white for running extra (as in not a scheduled train)
(Also note loco was changed from wood-burner it came as to a coal burner)
Also pilot deck from Plastruct treadplate sheet. Real one of this vintage likely was not treadplate but I like the visual texture. Plate still needs side sills added.
Control rod and lever for sand dome made out of brass wire and strip. Strip is press fit into slot made by drilling 3 holes then nibbling between with #11 blade.
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: on30gn15 on May 20, 2011, 06:40:38 PM
Post by: on30gn15 on May 20, 2011, 06:40:38 PM
Took eye pins and craft chain to make it possible to open knuckle by working cut lever.
Next question is how to color chain.
Next question is how to color chain.
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: on30gn15 on May 20, 2011, 07:11:00 PM
Post by: on30gn15 on May 20, 2011, 07:11:00 PM
Next thing is, need to find eagle casting for sand dome top like this N&W 4-6-0 http://spec.lib.vt.edu/imagebase/norfolksouthern/full/ns576.jpeg
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: NarrowMinded on May 20, 2011, 07:30:31 PM
Post by: NarrowMinded on May 20, 2011, 07:30:31 PM
What is the chain made from? brass steel plated? I often just heat differant metals over a fire then let them cool many turn black. steel chain usually rusts when the water dries, but I like the rust!
NM
NM
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: on30gn15 on May 20, 2011, 07:34:49 PM
Post by: on30gn15 on May 20, 2011, 07:34:49 PM
Quote from: NarrowMinded on May 20, 2011, 07:30:31 PMWhat is the chain made from?Uhhhh . . . good question.
Hang on a minute.
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: on30gn15 on May 20, 2011, 07:38:36 PM
Post by: on30gn15 on May 20, 2011, 07:38:36 PM
Took back of #11 blade and scraped one link to where it had flat spot and inside looks just like outside.
Package is a couple years gone. Came from one of the craft stores' jewelry sections.
That's the end of what I can give in response.
Package is a couple years gone. Came from one of the craft stores' jewelry sections.
That's the end of what I can give in response.
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: Model Tug on May 21, 2011, 10:08:45 PM
Post by: Model Tug on May 21, 2011, 10:08:45 PM
I have used "Blacken-it" available from Micro-Mark (for brass)
4 oz for $8.95 plus shipping
Rod
4 oz for $8.95 plus shipping
Rod
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: on30gn15 on May 22, 2011, 11:32:28 AM
Post by: on30gn15 on May 22, 2011, 11:32:28 AM
Ahh! That is a good idea, Model Tug.
In photo below: have been looking a loco plans and photos which could be located of that era of engines.
Because that long of a sand control rod, something like 11 feet long, would be too bendy - there has to be a guide bracket somewhere.
Think in a couple photos of narrow-boiler locos there is one from handrail to control rod. But on this one they are much further apart.
Hmmmmm...............?
In photo below: have been looking a loco plans and photos which could be located of that era of engines.
Because that long of a sand control rod, something like 11 feet long, would be too bendy - there has to be a guide bracket somewhere.
Think in a couple photos of narrow-boiler locos there is one from handrail to control rod. But on this one they are much further apart.
Hmmmmm...............?
Title: Re: Homemade details for Glenbrook Valley 4-6-0
Post by: Loco Bill Canelos on May 23, 2011, 01:44:53 PM
Post by: Loco Bill Canelos on May 23, 2011, 01:44:53 PM
I just paint the chain red oxide!!