Bachmann Online Forum

Discussion Boards => HO => Topic started by: MrMoose on January 07, 2015, 08:47:02 AM

Title: E-Z track turnout wiring
Post by: MrMoose on January 07, 2015, 08:47:02 AM
Hi,
I want to replace the switch that comes with the remote turn out to a DPDT switch. I understand how to wire a momentary DPDT switch to operate the turnout but I don't understand how to wire the three wires that the turnout uses to the DPDT switch.
Title: Re: E-Z track turnout wiring
Post by: Doneldon on January 07, 2015, 09:25:35 AM
Moosie-

The center terminal on the remote turnout is the neutral or common. One of the others is for the straight track; the
other is for the diverging track. If you get the directions wrong, just exchange them.
                                                                                                                              -- D
Title: Re: E-Z track turnout wiring
Post by: Len on January 07, 2015, 09:42:30 AM
I can tell you from personal experience, these work quite well: http://www.grainger.com/product/POWER-FIRST-Toggle-Switch-2VLT2 (http://www.grainger.com/product/POWER-FIRST-Toggle-Switch-2VLT2)

Unless you want the extra contacts for signal lights, you only need a SPDT Momentary On-Off-On switch, not a DPDT.

Tie all the center wires (common) together and connect to one side of your power supply. The outside wires go to the outer connectors on the SPDT switch. The switch center connectors can be "daisy chained" together, and connect to the other side of the power supply.

Len
Title: Re: E-Z track turnout wiring
Post by: MrMoose on January 07, 2015, 09:46:35 AM
Thanks guys, I thought that the center wire was common but wasn't sure.
Title: Re: E-Z track turnout wiring
Post by: Irbricksceo on January 07, 2015, 12:35:19 PM
I might just have to do this as well
Title: Re: E-Z track turnout wiring
Post by: jbrock27 on January 07, 2015, 12:54:53 PM
Because you like the look of the toggle switch or you don't like the look of an Atlas #56 controller?
Title: Re: E-Z track turnout wiring
Post by: Len on January 07, 2015, 01:00:07 PM
I prefer the toggle switches because you just have to tap them one way or the other. No sliding over, then pressing. And no burned out solinoids if someone, e.g., grandkids, sets something on the switch controller keeping the button pressed down.

Len
Title: Re: E-Z track turnout wiring
Post by: jbrock27 on January 07, 2015, 01:05:08 PM
Sure, I understand Len.  I was posing the question just to Brick as to why he felt the need to do this as well.

BTW, those toggles seem expensive.  Is that the going price?  I am going to implement some pushbutton momentaries in 2 colors to put on a control panel, myself.  The 2 colors will represent the 2 routs.
Title: Re: E-Z track turnout wiring
Post by: Irbricksceo on January 07, 2015, 01:56:15 PM
Couple of reasons. One, i Like the look and function of the toggles better, two, I lost two of my switch controllers and have one turnout  where the plug was severed anyway, and three, I bet I could wire both sides of the crossover to the same switch. Chalk it up to personal preference i guess.
Title: Re: E-Z track turnout wiring
Post by: jbrock27 on January 07, 2015, 02:03:44 PM
Got it Brick.

Len, not for arguments sake, but can't grandkids make the same mistake of holding down the momentary toggle in one postion too long as well?
Title: Re: E-Z track turnout wiring
Post by: Len on January 07, 2015, 02:18:08 PM
jbrock,

True, they could physically hold it to one side or the other.

But the problem I had, and why I switched to toggles, wasn't they were operating the switch on purpose for too long. They just kept setting things, mainly books, on top of the flat Atlas switch controllers. This would hold the button down, and I'd get fried switch machines.

The toggle handles, sticking straight up, are less inviting as a place to set things on.

Len
Title: Re: E-Z track turnout wiring
Post by: jbrock27 on January 07, 2015, 02:42:29 PM
Got it Len.  I have seen folks mount the #56s vertically along the frame of a layout; this would prevent anything from being laid on top of them.
Title: Re: E-Z track turnout wiring
Post by: Len on January 07, 2015, 03:06:58 PM
Might work, but I've gotten used to just flipping the toggle one way or the other. It just seems simpler than the 'slide/press' action of the #56, or equivalant, type of controller.

Len
Title: Re: E-Z track turnout wiring
Post by: jbrock27 on January 07, 2015, 03:32:12 PM
Oh yea, I am not trying to convince you to do anything different.  I was just putting that info out there for anyone who may want to consider that option, bc it does work.  Like I said, I think I am going to like the push buttons better as well.

The only problem I ever had with the 56s is some will no longer gang together using those right side tabs (forks) because they stopped conducting, for some reason.
Title: Re: E-Z track turnout wiring
Post by: jward on January 07, 2015, 08:04:39 PM
Quote from: Irbricksceo on January 07, 2015, 01:56:15 PM
Couple of reasons. One, i Like the look and function of the toggles better, two, I lost two of my switch controllers and have one turnout  where the plug was severed anyway, and three, I bet I could wire both sides of the crossover to the same switch. Chalk it up to personal preference i guess.


as long as your power supply has enough current to throw two switch motors simultaneously, you can wire both switches of a crossover together. I've done it many times. the mrc packs I used had enough juice to throw 3 motors, two threw the crossover switches, and the third was an atlas snap relay I used to power panel lights.

just make sure your are using the momentary toggles, the regular kind will burn out your switch motors.