Bachmann Online Forum

Discussion Boards => N => Topic started by: SMD4650 on January 20, 2017, 07:32:57 PM

Title: Wish to add DCC to 0-6-0 Locomotive
Post by: SMD4650 on January 20, 2017, 07:32:57 PM
I have a Bachmann 0-6-0 D&RGW locomotive that is analog.  Is there any way to make it DCC?  How would I do that?
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: spookshow on January 21, 2017, 06:28:57 AM
Bachmann's 0-6-0 is not DCC-Ready, so installing a decoder is not easily accomplished. The specifics would depend on which version you have (there have been many different revisions over the years), but basically you would need to isolate the motor from the chassis and then do a wired decoder install.

This is the most recent version (actually a 2-6-2, but the internals are the same as an 0-6-0), and as you can see there's not much room for a decoder. So, it'd probably have to go in the tender.

(http://www.spookshow.net/loco/files/bach262chassis2015.jpg)

-Mark
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: brokemoto on January 21, 2017, 10:52:59 AM
Quote from: spookshow on January 21, 2017, 06:28:57 AMThis is the most recent version (actually a 2-6-2, but the internals are the same as an 0-6-0), and as you can see there's not much room for a decoder. So, it'd probably have to go in the tender.



..........at which point an upgrade to the SPECTRUM tender would be necessary.
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: gatrhumpy on January 21, 2017, 01:42:46 PM
DCC in this engine is a pain in the butt. You have to switch tenders (the one it comes with is worthless), and then wire up the DCC decoder after you isolate the motor. I've done it. It's not fun.
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: Flare on January 21, 2017, 05:26:22 PM
Might a Digitrax Z scale decoder like the DZ126T fit in the cab?

Its dimensions are 14x7.13x3.25mm and it does a LOT for such a tiny board.

http://www.digitrax.com/products/mobile-decoders/dz126t/


I installed one in my On30 Mogul's boiler which also has very tight clearances.
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: spookshow on January 22, 2017, 07:53:00 AM
Quote from: Flare on January 21, 2017, 05:26:22 PM
Might a Digitrax Z scale decoder like the DZ126T fit in the cab?

Probably not. The motor pretty much fills up the entire cab -

(http://www.spookshow.net/loco/files/bach262.jpg)

-Mark
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: Flare on January 22, 2017, 12:16:49 PM
Quote from: spookshow on January 22, 2017, 07:53:00 AM
Probably not. The motor pretty much fills up the entire cab -

-Mark

True, but there appears to be some empty space ABOVE the motor.  ;)
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: plas man on January 22, 2017, 04:44:44 PM
try this - you may have to log/sign up the the forum ... (play nice  :) ).....

http://www.nscale.net/forums/content.php?63-Bachmann-0-6-0-Switcher-DCC-conversion-A-complete-how-too-(pic-heavy)

the contents are heavy with lots of images  :'(

plas man

edit ... found the original page with photos including fitting of de-coder - its a good write up .

http://www.nscale.net/forums/showthread.php?20301-Bachmann-0-6-0-Switcher-DCC-conversion-A-complete-how-too-(pic-heavy)&p=182287#post182287
Title: Re: Wish to add DCC to 0-6-0 Locomotive
Post by: Br 98.75 on January 24, 2017, 08:30:36 PM
I have done it several times with the older 0-6-0's my Durango and silverton is one of my favorite steam locos nets to the red and blacks and my UP FEF