News:

Please read the Forum Code of Conduct   >>Click Here <<

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - trainman203

#1021
HO / Re: Bachmann 2-8-4 Berkshire
February 15, 2023, 10:55:36 AM
There has to be plenty of those Berks around either on eBay, or at some discount house somewhere. I would not touch one called a project. They're telling you right upfront that there's problems with it, that's why it's not a running locomotive. If you need parts for one you already have, that would be the way to get them since there's probably very few available anymore from Bachmann.

I'd like to convert one of those engines to a Missouri Pacific/I-GN 1900, but the domes and the number boards and stuff on top of the smokebox front need just too much radical surgery to make it practical. Plus, the drivers are a good bit taller than on the MP engines. The nickel plate engines were known for running manifest freights at passenger train speed across a bridge route, unlike the slower-speed more typical freights that the MP engines with lower drivers handled.  Between the tall drivers and the extremely involved boiler alterations, it's a job for a much younger modeler with better eyes.  Besides, I am running a branch line. What would a 2–8–4 be doing running down my little branch?
#1022
General Discussion / Re: Models of less popular roads
February 15, 2023, 10:34:24 AM
Quentin, every HO steam locomotive on earth has wires between the locomotive and the tender. You cannot escape that. Back in the 1960s, when DC ruled the model railroad rail, and only one wire was required from the tender to the motor and the locomotive, wireless drawbars that conducted power between the locomotive and the tender began to become popular. But with today's engines, there's just too many functions in play to have only one wire between the two units.

There are ways to redirect these wires around to not cause problems. Sometimes, they can be quite squirrelly in refusing to be positioned properly. But with work and patience, it can be done. Sometimes you have to far–connect the engine and tender to allow stiff wires some room to flex. It's true, that wrongly directed wires can cause the tender to chronically derail. But I wouldn't let that keep me from buying an engine I want.

I'd have to count again, but I believe I have at least 50 HO steam locomotives, all with DCC and sound, every one of them with wires between the engine and the tender. I'd have to say that 3/4 of them needed some kind of doctoring to keep the wires from derailing the tender on some curve or switch or something. Fixing that problem is just one more skill  to add to your Model Railroad toolbox.
#1024
On steam engines, CV 116 is the chuff rate.
#1025
Cv 116 is the chuff rate in sound value.  If there is automatic silencing, I'd like to know.  Lack of it is my biggest problem with sound value.

I have tsunami2-2 in about 3/4 of my engines now.  The rest are a mixture of older tsunami's, the old Bachman Soundtraxx on-board sound, and a couple of Econamis.  I've worked with Soundtraxx products for so long I've become one with them.  I have a couple of BLI engines with paragon sound and dislike it for many reasons.
#1026
Why would anyone want automatic sounds?  Except maybe on a continuously running display layout.

Sound value, to me, has a lot of missteps in the choices of sounds and options made available. Probably the biggest erroneous omission, to me, is CV 113, the automatic silencing and keeping an engine silent until activated.  And the coupler crash.  Why the automatic sounds are taking up bytes in this basic level system is beyond me. Along with headlight dimming, which is a diesel era affectation and useless on steam locomotives.

I'd still rather any Soundtraxx products over TCS, though.  TCS is keeping me from buying a new decapod.
#1027
General Discussion / Re: Wabash and Gulf Mobile & Ohio
February 13, 2023, 10:55:44 AM
Look at that perfectly ballasted, perfectly neat, and flawless track work. Those were the days!
#1029
General Discussion / Re: Models of less popular roads
February 11, 2023, 07:58:56 PM
Back to original topic. Quentin, follow the examples I put up for stand-in Missouri pacific steam engines and you can build quite a roundhouse-full of acceptable locomotives for that road. Accurate MP steam engine decals can be had from the Missouri Pacific historical society.

Bachmann engines aren't the only ones I have. I have four other mikados by another vendor, plus a couple of Bachmann 10 wheelers lettered for the MP that I did not even mention, so I believe I have about 15 or 16 MP steam engines in my Roundhouse... quite likely one of the larger MP steam rosters in the model railroad world.

In addition, I have MP diesel power consisting of 4 GP7's and an A B A set of F units... though they only run on other layouts.

I have a few steam engines for other roads too, like the Frisco, KCS and the Rock Island, my only requirement being that they ran in the ArkLaTex region. A Cotton Belt steamer is planned.

I haven't touched on my steam engines for southern roads east of the Mississippi.
#1030
General Discussion / Re: Models of less popular roads
February 11, 2023, 11:57:05 AM
I'm pretty sure this is it

https://en.m.wikipedia.org/wiki/GE_BQ23-7

The B29 nose is a quirk of memory.  It's been so long since I saw it.  I do remember it being SCL now.

#1031
General Discussion / Re: Models of less popular roads
February 11, 2023, 08:26:49 AM
No. It was a road switcher with four wheel trucks from maybe the late 60s, certainly the 1970s. I was given a model of it in the early 80s when I begin to think about a layout and talked about it some. Couple or three people gave me models, diesels, and this very unusual road switcher was one of them. Think B 29 or B 36 faceted glass nose. That's what the front of this locomotive looked like. It was the weirdest looking thing I've ever seen on rails. 

I never unboxed any of them. Really should have. I didn't understand that I could've had a 2x8 switching layout using the three or so road switchers I had. I had that peculiar locomotive, an Athearn SD9, and  an S2 and RS2 or something by Atlas. Plus a dozen  or so freight cars that had survived 20 years in the attic.  All burned up in a fire.
#1032
General Discussion / Re: Models of less popular roads
February 10, 2023, 05:57:12 PM
My model might have been a bachmann.  It's probably 30 yr since I last saw it.  It was Chessie.  Never ran it, it was a gift.  No space for layout back then.  I think it was an EMD engine.  Can't remember for certain.
#1033
General Discussion / Re: Models of less popular roads
February 10, 2023, 05:23:30 PM
No one knows yet what the diesel was with the B–29 cockpit for a cab? I had a model of it years and years ago, was lost in a house fire.
#1034
HO / Re: EMD E3 & E4 Diesel-Electric Streamliners
February 10, 2023, 09:15:17 AM
I saw those KCS shovel noses on a trip to New Orleans as a kid.
#1035
General Discussion / Re: Models of less popular roads
February 09, 2023, 08:44:38 PM
https://en.m.wikipedia.org/wiki/EMD_MRS-1

"Military Road Switcher". Haha. I like it.  A great idea too late for practical use.  Homely, I have to say.

About the truly most homely diesel I ever saw, I can't remember the name of.  It looked like a GP7 but instead of a short hood it had a cab that looked like the faceted glass nose of a B-29.  Someone knowledgeable remind me what it was.