ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES

Welcome, Guest. Please login or register.
Did you miss your activation email?
October 22, 2019, 07:55:56 AM
Home Help Search Login Register
News: Please read the Forum Code of Conduct   >>Click Here <<
  Show Posts
Pages: [1] 2 3 ... 11
1  Discussion Boards / General Discussion / Re: Managing dust in the layout room on: August 12, 2015, 12:23:11 PM
i have a whole house floor mounted hepa filter for my train room. on low speed(very little noise) it keeps the entire room dust free... my room is also in my finished basement and the room itself is completely finished so that helps.
2  Discussion Boards / General Discussion / Re: Check out my next house... on: July 16, 2015, 01:37:30 PM
ive run my locomotive and tom's k36 there 10 years ago. very impressive place
3  Discussion Boards / Large / Re: Posts on: October 16, 2014, 12:17:20 PM
mine are centered.. and its been this way for 2 weeks.... only this site
4  Discussion Boards / General Discussion / Re: Constanly Cleaning my layout track on: May 28, 2014, 12:02:04 PM
i have a house filter unit in my train room with a hepa filter, i leave it on all the time on low speed,  never have any dust in my room, however mine is a finished room which will make a huge difference...
5  Discussion Boards / On30 / Re: desk top auto reverse system on: March 14, 2014, 04:52:49 PM
The ON30 equipment runs on HO track as you know.  So it will fit fine

As far as current draw from a larger loco, many of my ON30 locos have smaller n scale decoders in them
So it shall work just fine
6  Discussion Boards / General Discussion / Re: Xmas train won't work and it is brand new on: November 17, 2013, 01:17:20 PM
Ok. That's a bachmann g scale wonderland flyer. Ac not dcc.

Are you certain that the track power is plugged into the track power output connection on the power pack and not the accessories connection?
7  Discussion Boards / General Discussion / Re: Xmas train won't work and it is brand new on: November 17, 2013, 12:08:03 PM
The gauge is on the box and in the instructions. How about a model number?  That will also tell you if it's a dcc set.  You have to read a bit and have some info before anyone can help you. We cannot guess for you.
8  Discussion Boards / General Discussion / Re: Needed help! on: November 14, 2013, 08:48:56 PM
He said engine to tender.  That would be the drawbar.  And piece of plastic with holes drilled in it will work
9  Discussion Boards / On30 / Re: replacement gears on: November 10, 2013, 06:17:23 PM
Linzthom. This is rediculous.    How much will it cost to mail your parts from Washington state, us to NZ? 

I will send an email asking for my replacement gears. And when they arrive, mail them to you.  Message me what gears you need. I can't believe this is still going on.  It took two times to get my gears.
10  Discussion Boards / On30 / Re: replacement gears on: September 23, 2013, 11:21:38 PM
Same deal here.  Got my first email right away no parts.  Requested a second time and had them In a week.  Try again
11  Discussion Boards / On30 / Re: REPLACEMENT GEARS on: August 11, 2013, 06:15:31 PM
STILL haven't received anything.  I figure I'm not going to by now. Got my email from Bridget 4 weeks ago....
12  Discussion Boards / General Discussion / Re: Speed Controller on: June 17, 2013, 10:10:11 PM
Is it possible that the track is hooked up to accessory terminals?
13  Discussion Boards / On30 / Re: Climax grade climbing on: May 20, 2013, 10:19:26 PM
I've got 4% with curves and my climax pulls a string up it just fine your rear truck seems to be unpowered
14  Discussion Boards / On30 / Re: dcc questions on: March 29, 2013, 08:27:03 AM
1st question. Are you putting the decoder plugs in the correct orientation? Pin 1 must go in socket 1
15  Discussion Boards / General Discussion / Re: dEISEL WON'T RUN on: February 19, 2013, 11:06:53 PM
If the bells and  horns work. He's got the right address and the pickups are working fine
Pages: [1] 2 3 ... 11
Powered by SMF | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!