ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES

Welcome, Guest. Please login or register.
Did you miss your activation email?
July 21, 2019, 12:48:55 AM
Home Help Search Login Register
News: Check out the photo gallery link above or >click here< to see photos of recently announced products!
  Show Posts
Pages: [1]
1  Discussion Boards / HO / recommended 8 pin decoder for s2/s4 dcc ready locomotives on: March 13, 2018, 08:51:40 PM
Need help with 8 pin decoder se.lection for s2/s4 switcher. Shell is Milwaukee Road #816 with only one front light rather than two shown currently.

Thaks
2  Discussion Boards / General Discussion / Re: Can EZ Command be programmed to be used with MRC 1628 decoder? on: January 31, 2018, 10:13:33 PM
Thanks for reply. Was hoping but know limited capability of EZ Commend system.
3  Discussion Boards / General Discussion / Can EZ Command be programmed to be used with MRC 1628 decoder? on: January 29, 2018, 10:34:54 PM
Have seen MRC 1628 (4 solenoid) decoder board programmed with NCE and MRC systems to run this decoder. Can EZ Command system also be used if addresses are 1-8. Have 6 turnouts?

Curt Doduff44
4  Discussion Boards / General Discussion / Re: Bachmann Locomotive Part Number Reference Listing on: January 27, 2014, 08:02:22 PM
richg

Thanks for reply.

At this time looking at American 4-4-0. Picked up one on Ebay that has Virginia & Truckee tender and pancake motor (Needs drive shaft and wire from tender to loco).
Have diagram from Ho Seeker site. Also newer Atlanta & West Point from Civil War set.

Number of units on Ebay are different names/colors than current Bachmann website.

Can current driveshaft fit old design?
5  Discussion Boards / General Discussion / Bachmann Locomotive Part Number Reference Listing on: January 27, 2014, 03:45:17 PM
I have noticed a number of different part numbers for similar Bachmann Locomotives on Ebay and hobby stores sites. Is there a listing of models by release date and part number available?

Thanks
6  Discussion Boards / General Discussion / Re: Wiring feeder lines with EZ track on: January 11, 2014, 09:56:20 PM
Donelson:

Have number of terminal tracks and supply of red wires so will try on simple oval to see if works. Currently have 4x8 plus 4x4 addition size layout. Two DCC with sound run Ok but think I need better distribution of power. Using Bachmann EZ Commander system which works graet so far.

Curt
7  Discussion Boards / General Discussion / Wiring feeder lines with EZ track on: January 09, 2014, 09:53:18 PM
Can you locate 9" terminal track around layout and plug in red wiring to each one and then splice all to main red wire from EZ commander?

Thanks

custerg911
8  Discussion Boards / General Discussion / Re: Best way to attach EZ track to form - type of gum? on: May 13, 2013, 01:41:05 PM
Thanks JerryHO and Doneldon:

Have you tried Foam Tack Glue by Woodland Scenic on cork or their foam incline/riser products?

Curt
9  Discussion Boards / General Discussion / Best way to attach EZ track to form - type of gum? on: May 11, 2013, 09:16:44 PM
New to forum - so ? may have been asked before. EZ track on both flat and grade.

Thanks

CurtN
Pages: [1]
Powered by SMF | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!