Home
ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
January 16, 2021, 05:31:01 PM
News:
Please read the Forum Code of Conduct
>>Click Here <<
Bachmann Message Board
Discussion Boards
Large
g-scale engines run shakey at times
« previous
next »
Pages:
[
1
]
Author
Topic: g-scale engines run shakey at times (Read 2946 times)
tiger88mm
g-scale engines run shakey at times
«
on:
June 16, 2013, 02:23:31 AM »
I have several Bachmann g-scale engines ( 0-4-0,4-6-0, a two truck shay and a heisler ),they start out fine then will start to jerk/sputter for a few feet then run fine and then starts all over again,track is clean and polished ,connections are tight ,drive wheels and trucks are clean,my other engines run fine with no problems,where do I need to look or do to make this engines run again,thanks-=
Logged
Joe Zullo
Re: g-scale engines run shakey at times
«
Reply #1 on:
June 16, 2013, 02:18:32 PM »
Look to the electrical pickups from the wheels to the motor. They could be dirty or not making proper contact.
Logged
Tom Lapointe
Re: g-scale engines run shakey at times
«
Reply #2 on:
June 17, 2013, 10:54:09 PM »
If
all
the engines run the same way, you could also have a problem with your power pack or feed lines to the track. Is this an indoor or outdoor layout, & what type of track? In addition to dirty electrical pickups, jerky operation can be caused by poor electrical joints between rail sections. Watch if the problem occurs over specific sections of track; often the resistance of a poor joint will change as the weight of the locomotive passes over it. How old are the locomotives? - The Shay in particular? Early production Bachmann Shays had problems with the electrical pickups overheating & causing the plastic supports to deteriorate. Best cure is to replace the original equipment trucks with the upgraded die-cast trucks (which come "standard" on the later production "38-ton" (steel-cab version) of the Shay; the later ones are excellent runners.
Tom
Logged
Joe Zullo
Re: g-scale engines run shakey at times
«
Reply #3 on:
June 18, 2013, 07:42:57 AM »
Quote from: Tom Lapointe on June 17, 2013, 10:54:09 PM
If
all
the engines run the same way, you could also have a problem with your power pack or feed lines to the track. Is this an indoor or outdoor layout, & what type of track? In addition to dirty electrical pickups, jerky operation can be caused by poor electrical joints between rail sections. Watch if the problem occurs over specific sections of track; often the resistance of a poor joint will change as the weight of the locomotive passes over it. How old are the locomotives? - The Shay in particular? Early production Bachmann Shays had problems with the electrical pickups overheating & causing the plastic supports to deteriorate. Best cure is to replace the original equipment trucks with the upgraded die-cast trucks (which come "standard" on the later production "38-ton" (steel-cab version) of the Shay; the later ones are excellent runners.
Tom
I guess you missed this part of the OP.....
"...my other engines run fine with no problems..."
Logged
Dave
Re: g-scale engines run shakey at times
«
Reply #4 on:
June 18, 2013, 04:18:59 PM »
You need to tell us, What power supply you are using, What are the other Locomotives and if you are using Linear or PWM.
Dave
Logged
Loco Bill Canelos
Model railroading since 1947
Re: g-scale engines run shakey at times
«
Reply #5 on:
June 18, 2013, 06:01:53 PM »
Tiger, I am sure we can help if we can isolate the many possible problems. How long has it been since these engines were last run before the problems began, Did it happen suddenly? Did they all work fine the last time you used them? Also let us know the grades you are operating on and better yet a video of each engine showing the problem. It is highly unusual for all four of your Bachmann engines to display the same result when they have different pickup systems, especially the shay.
From your description it might be that something is tripping or trying to trip the thermal breaker on you power supply. Many are thermal and reset themselves. I have seen this as a cause before so it might be worth checking out. Another possibility could be a loose wire or connection, but it isn't likely on four seperate engines at the same time.
Bill
Logged
Loco Bill, Roundhouse Foreman
Colorado & Kansas Railway-Missouri Western Railway
Official Historian; Bachmann Large Scale
Colorado RR Museum-Brakeman-Engineer-Motorman-Trainman
There are no dumb or stupid questions, just questions!
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Discussion Boards
-----------------------------
=> General Discussion
=> E-Z App
=> Large
=> Williams by Bachmann
=> On30
=> Plasticville U.S.A.
=> HO
=> Thomas & Friends
=> N
-----------------------------
Frequently Asked Questions (F.A.Q.s) - READ ONLY FORUM
-----------------------------
=> General Questions
=> Large Scale
=> Williams by Bachmann
=> On30
=> HO
=> N
=> DCC
Powered by SMF
|
SMF © 2015, Simple Machines
Loading...