ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES

Welcome, Guest. Please login or register.
Did you miss your activation email?
December 12, 2019, 04:57:52 PM
Home Help Search Login Register
News: Check out the photo gallery link above or >click here< to see photos of recently announced products!
+  Bachmann Message Board
|-+  Discussion Boards
| |-+  HO
| | |-+  5 amp booster and Dynamis with Pro Box- -The Solution!!!
« previous next »
Pages: [1] Print
Author Topic: 5 amp booster and Dynamis with Pro Box- -The Solution!!!  (Read 1307 times)
JimJim

View Profile
« on: March 30, 2016, 03:39:01 PM »

Hello all,

Here's what I did...And it worked!

I had a spare mini-plug to 1/8-inch cable. I also had a mini-plug to bare wire; that came with my Dynamis system and the screw terminal connector block that came with the Probox.

I cut the 1/8-inch end off of the mini-plug to 1/8-inch cable. I stripped the outer jacket being careful not to nick the insulation on the inner wires or the un-shielded third conductor (bare strands).

Because all the connectors are tip/ring/sleeve I used my multi meter on the continuity setting and determined the conductor
configuration.

As it turns out the red inner wire (tip) is not used. The white wire and the bare copper are the conductors. (There is a diagram on the booster that confirmed this.)

Tip=Not Used
Ring=Positive (red)
Sleeve=Negative (black)

Then I metered between the sleeve receptacle on the Dynamis Command Station and the output pins on both the Command Station and the Pro Box.

Looking at both units the pin on the left side is the white conductor (ring) the pin on the right side is the bare copper (sleeve).

Next, I marked the mini-plug to bare wire conductor with a black permanent marker; sleeve=black, ring=red (no color needed).

Then I used the screw terminal connector block and attached the white (ring) wire to the left terminal and the bare conductor (sleeve) to the right terminal.

I plugged the 1/8-inch connector into the booster from the Pro Box/screw terminal connector block. The booster already had the red output connected to the right rail and the black output to the left rail. (Make sure that both outputs from the Pro Box and the booster connect to the same rail maintaining polarity.)

Then, as per the Pro Box instructions, I used two insulated rail joiners to isolate the programming track. Using color coded (red & black) terminal joiners I attached the mini plug to bare wires to the correct polarity on the programming section (pg. 3 Dymanis Pro Box User Guide).

I then powered up the Dynamis Command Station/Pro Box, then the booster and finally turned on the handset.

Then I ran a know addressed locomotive from the main track to the programming track with no problems.

Next I took another locomotive, placed it on the programming track and read the address correctly.

Now I have the Pro Box AND the 5-Amp booster working in conjunction along with a programming track.

This solution would be a simple "Fix" from Bachmann by supplying OEM produced cables that I cobbled together.

Hope this helps!
« Last Edit: March 30, 2016, 03:41:00 PM by JimJim » Logged

“Uhh...I didn’t know it was ‘impossible’ I just made it work...sorry!”
brokenrail

View Profile
« Reply #1 on: April 06, 2016, 11:03:35 AM »

I was thinking about purchasing a pro box,but I really do not see any benefit to it .It will give read back and what else? There is still no way to interface with a pc still, or has that changed? Dynamis alone has the power here to run, as far as I have tried, 4 sound locomotives on a 2 track scale mile and a half layout with spurr tracks with no power drop outs,brown outs ect... A 2 dollar switch can be used to turn on and off a isolated programming track.What else is there for 2 to 3 hunderd dollars.Mirrors can be set up in the train room to aid the infrared receiver to completely eliminate  connection losses from the hand held to the receiver.
So what justifies the cost? Am I missing Something
Johnny Huh??
Logged
Bucksco

View Profile
« Reply #2 on: April 06, 2016, 11:57:05 AM »

The Pro Box enables the user to add 3 more receivers to their layout for a total of 4 in addition to being able use programming tracks to read and write CVs..
Logged
Pages: [1] Print 
« previous next »
Jump to:  
Powered by SMF | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!