Home
ONLINE
STORE
"ASK THE BACH MAN"
FORUM
PARTS, SERVICE,
& INFORMATION
CATALOGS AND
BROCHURES
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
February 23, 2019, 07:59:06 PM
News:
Check out the photo gallery link above or
>click here<
to see photos of recently announced products!
Bachmann Message Board
Discussion Boards
General Discussion
Unplug Controller?
« previous
next »
Pages:
[
1
]
Author
Topic: Unplug Controller? (Read 1601 times)
DAVISinGP
Unplug Controller?
«
on:
December 13, 2017, 05:39:30 PM »
Hi all,
I’m new to the hobby and am greatly enjoying my Bachmann Digital Commander.
I’ve already found very useful information on this forum as a lurker for the past couple of months. Now as a member, I’ll no doubt have many questions. So here’s the first.
I’m curious what the general feeling is about unplugging the controller (DCC) when not in use. I’ve been leaving it plugged in overnight (turned ‘off’ of course) unless I’m going to be away for a few days. I'd prefer to leave it plugged in if there is no danger of damage.
There’s probably no agreed-upon answer, but I am curious as to what Bachmann recommends and what others do.
Thanks.
Logged
Flare
Re: Unplug Controller?
«
Reply #1 on:
December 13, 2017, 05:55:17 PM »
I always unplug my layout when not in use.
If something creates a short circuit I want to be present to correct the problem.
Logged
DAVISinGP
Re: Unplug Controller?
«
Reply #2 on:
December 14, 2017, 10:27:41 PM »
Thanks for your feedback. (It's a bit quiet in here, eh?
)
Logged
jward
Re: Unplug Controller?
«
Reply #3 on:
December 16, 2017, 11:43:12 AM »
you could, and should, plug it into a surge protector. That way, you can flip the on off switch on the surge protector to kill power to the layout. I've done this for years with no problems.
Logged
Jeffery S Ward Sr
Pittsburgh, PA
DAVISinGP
Re: Unplug Controller?
«
Reply #4 on:
December 16, 2017, 11:35:15 PM »
That's a good idea.
My concern about unplugging the controller was that it might lose its memory (i.e. DCC addresses) if unplugged for a while.
Logged
Flare
Re: Unplug Controller?
«
Reply #5 on:
December 16, 2017, 11:59:54 PM »
That's a possibility if left alone long enough, that's why it's a very good idea to write down addresses, CVs, and other non-factory changes you make in case they need to be reprogrammed.
Logged
jward
Re: Unplug Controller?
«
Reply #6 on:
December 17, 2017, 07:25:51 AM »
FLare, don't give inaccurate info. Addresses, CVs and the like are stored in the decoder, not the controller. There is no danger of losing them if the controller is unplugged. If this info was stored in the controller, you'd have to reprogram the decoder every time you took your locomotives to a train club, a friend's layout, etc. The fact that you don't is proof this info is in the decoder.
Logged
Jeffery S Ward Sr
Pittsburgh, PA
2foot6
Rail bus on Martins Creek Tramway
Re: Unplug Controller?
«
Reply #7 on:
December 17, 2017, 08:32:39 AM »
Even though I use a different DCC system ,I always turn off the power when not in use.I have done this for the last fifteen years with no problems.........Peter.
Logged
I ASPIRE TO INSPIRE BEFORE I EXPIRE.
Flare
Re: Unplug Controller?
«
Reply #8 on:
December 17, 2017, 02:20:49 PM »
Quote from: jward on December 17, 2017, 07:25:51 AM
FLare, don't give inaccurate info. Addresses, CVs and the like are stored in the decoder, not the controller. There is no danger of losing them if the controller is unplugged. If this info was stored in the controller, you'd have to reprogram the decoder every time you took your locomotives to a train club, a friend's layout, etc. The fact that you don't is proof this info is in the decoder.
Yes, but what is the lifespan of the data in the decoders? I've read that solid state memory can be lost if left unpowered long enough.
http://www.extremetech.com/computing/205382-ssds-can-lose-data-in-as-little-as-7-days-without-power
Logged
jward
Re: Unplug Controller?
«
Reply #9 on:
December 17, 2017, 04:34:11 PM »
Loss of data hasn't been a problem with usb drives, and if it were a major problem with decoders, don't you think people would give up on DCC? Nobody wants to reprogram decoders every time they want to run trains.
Logged
Jeffery S Ward Sr
Pittsburgh, PA
Pages:
[
1
]
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Discussion Boards
-----------------------------
=> General Discussion
=> E-Z App
=> Large
=> Williams by Bachmann
=> On30
=> Plasticville U.S.A.
=> HO
=> Thomas & Friends
=> N
-----------------------------
Frequently Asked Questions (F.A.Q.s) - READ ONLY FORUM
-----------------------------
=> General Questions
=> Large Scale
=> Williams by Bachmann
=> On30
=> HO
=> N
=> DCC
Powered by SMF
|
SMF © 2015, Simple Machines
Loading...