I have a 2-4-4 Forny made by Spectrum and when I purchased it at the train show at a very good price , I had no place it run it , so on a keep of faith it came home with me. It was very clean, so onto my test track it went. It ran speed up and down and that was it. No head light, fire box flicker Cab, or back up light. To many electrical malfunctions, so off to the work bench. To my shock, there was no plug and play  board where one should be except for a makeshift board. So I need a plug and play priortity electronic board to plug into the main mother board. Does anyone have one witch you could have hanging around which you can donate to Me or I can pay fore.  HELP ME PLEASE

Quote from: RGSNH on July 01, 2026, 07:19:26 AMI have one from a bachman C-19, is that what you are looking for?

drop me a PM and we can discuss $$ and shipping.

Al p.

yes I would like to purchase your hole kit and cabotal of parts for $45.00 US dollars plus what you need for shipping. Also I am not that computer friendly, can you send me your IP code per e-mail address would even be, be better. Thanks Doug -  aka mudhen

Quote from: RGSNH on July 01, 2026, 07:19:26 AMI have one from a bachman C-19, is that what you are looking for?

drop me a PM and we can discuss $$ and shipping.

Al p.

Yes that is what I need and am looking for. How much do you want for this item with shipping to 15 Birchwood Drive, Barrie Ontario, Canada, L4M-4W7  Thanks in Advance, Doug. If you want to call me , call 416-894-6236 or e-mail me at [email protected]

It's been along time since I have been on this board and miss you all. I am in need of of a dummy board that fits into the plug and play board the tender to made the engine lights in the cab, head light work, firer box flicker and marker lights work. I had one but sent it to someone on this sight that needed one some years ago back. Would anyone have one they don't need ,Thanks in advance Doug will pay for it.

It's been a while since I have purchased any 1:20.3 Bachmann steam engines and I would like to know what you guys think a used or new C-19 # 346 should be worth and same question for me K-27 # 456. Thanks in advance for any help.

Would someone be able to tell me the original cost of the C-19 # 345 or #346. black in colour with the flying Rio Grande on the tender. Also what would be a reasonable price to pay for one today if one could be found. Thanks in advance.

Does anyone know where I can get drawing of the C-19 road pilot with dimensions to build one like the Bachmann C-19 one.                                                                                       How about you Mr Bachmann, any suggestions please.

Does anyone have a road pilot for the K-27, looking to replace a damaged one.

Thanks for your help, I will now look to purchase some JIS screw drivers and see how they work to remove those screws

Is there anyone out there that can get me the dimensions of the road pilot by Bachmann.
Thanks in advance if you can help.

Does anyone need tender switcher steps for a K-27 ( used in excellent condition )
Engine switcher pilot ( used in excellent condition )
I also have a BACHMANN - Dog House in unopened wrapper
All are for sale or trade for K-27 / C-19 Road Pilots

Does anyone in the 1:20.3 community have a spare road pilot for the K-27, made
by Bachmann and the the Bachmann road pilot for the C-19.
I am willing to pay for each if available.
I think I just purchased the only remaining, K-27 road pilot on the internet and need 1 more.
Thanks in advance if you can help.

I am attempting to remove screws on my K-27, witch hold on the tender road switcher long steps,
under the rear coupler, witch are no long required and on the C-19, again removing the
tender switcher steps, witch are again, under the coupler, and no longer required.
My problem is removal of the tiny, little screws that hold them on, and replace with proper road steps.
I have tried using phillips #0 and the smaller #0-2 with almost not luck upon extraction of the screws
holding the steps on. Usually 2 screws per side.
Short of using a vice grip on the head of the crew, and twisting them out. witch to date is my only option,
so far, does anyone have any suggestions or instruction of how you have removed these little buggers,
and without ruining the heads of them so they can be reused to put on steps.

To the Bachmann,
Now that the D&RGW's T-12 #169 is back in service,
Is Bachmann Industries, considering, manufacturing the T-12 engine in the 1:20.3 scale.
I know all about tooling, costs etc, blah, blah, blah.
I would like an honest answer of ,
Yes we will be manufacturing it, and when.
Very seriously considering it, and that's all.
Have no intension of manufacturing it, even in the now or in the near future.
I myself and many of the 1:20.3 scale friends would like a honest answer.
Thanks in advance for your answer, relieving may of us of the unanswered question.
We your devoted customers can handle the truth.
Again Thanks Mudhen,